Geotechnical Engineering · UMass Amherst

Morteza Shafiei

Ph.D. Candidate & University Instructor

I study glauconite sand, a green, iron-rich sand found along the U.S. Atlantic coast where offshore wind farms are being built. Its soft grains crush under load, so the soil can shift from sand-like to clay-like behavior during foundation installation. My research measures how, and how much, it degrades, to help engineers predict soil properties and avoid costly pile-driving refusal offshore.

Department of Civil & Environmental Engineering, University of Massachusetts Amherst. Advised by Prof. Don J. DeGroot, Sc.D., P.E. and Prof. Zachary J. Westgate, Ph.D., P.E.

FeaturedARROW offshore wind · Student Spotlight, Nov 2025
Portrait of Morteza Shafiei on the UMass Amherst campus in autumn
Amherst, Massachusetts
  • 62–72 Ma Age of the Hornerstown & Navesink glauconite sands I test, spanning the K–Pg boundary
  • 50 MPa One-dimensional compression used to mimic the soil beneath an advancing pile toe
  • 1 h–90 d Pile setup tracked with static load tests in a calibration chamber
  • 3,000+ Particles per material scanned by X-ray micro-CT to link 2D images to 3D shape

01 · About

Soil that turns from sand to clay

I am a Ph.D. candidate in geotechnical engineering at the University of Massachusetts Amherst and a student researcher with ARROW, the Academic Center for Reliability & Resilience of Offshore Wind. My work focuses on glauconite sand, which is common along the U.S. Atlantic continental shelf in areas of offshore wind development. Glauconite grains are soft (Mohs hardness of about 2) and crush easily, so this “greensand” can change from sand-like to clay-like behavior, a risk for both foundation installation and long-term performance.

I study how glauconite behaves under static and cyclic loading, and I am developing laboratory methods that mimic foundation installation, so we can determine how crushing changes soil properties and how much the sand degrades, using both laboratory and in-situ testing. Better predictions of these properties can reduce extensive and costly testing and the chance of pile-driving refusal offshore, where remediation can cost orders of magnitude more than on land.

Before UMass, I earned my M.Sc. at Amirkabir University of Technology (Tehran Polytechnic), where I designed and operated a large consolidation chamber to measure how piles in clay gain capacity over time. Today I also teach undergraduate engineering mechanics and geotechnical courses and work with undergraduate researchers in the laboratory.

02 · Research

Research areas

Across these projects, the common thread is linking what we measure in the laboratory to how soils behave in the field, from the grain scale to full-size piles.

  • Glauconite & crushable sands
  • Offshore wind geotechnics
  • In-situ testing (CPTu)
  • Pile setup & deep foundations
  • Physical modeling
  • Particle morphology

Ph.D. research · offshore wind

How glauconite sand degrades

Glauconite sands from the Hornerstown and Navesink formations (New Jersey) are degraded in the laboratory with methods matched to the stress regimes around a driven pile: one-dimensional compression, ball milling, and dispersion-cup mixing. I track the changes in grain size and plasticity, and how far each method breaks the particles down.

Key insightGrain size alone cannot classify degraded glauconite. How the fines are produced, through stress regime and free water, controls whether the soil becomes plastic.

See Figure 1

Offshore site investigation

Reducing CPTu thrust in glauconite sand

Crushable glauconite combines high cone resistance with high rod friction, which can stop a piezocone (CPTu) early. In a field program at a New Jersey site in two glauconite formations, part of the Piling in Glauconitic Sand (PIGS) Joint Industry Project, we compared larger cones, friction reducers of different length and diameter, multiple reducers, and water jetting.

Key resultA larger 15 cm² cone, a larger-diameter reducer, and upper-bevel water jetting significantly reduced thrust; longer or multiple standard reducers did not.

See Figure 2

Deep foundations · M.Sc. research

Pile setup in clay, measured in a calibration chamber

In a 400 mm × 1000 mm consolidation chamber, an instrumented CPT-size model pile (three strain gauges and three pore-pressure transducers) was driven or jacked into kaolinite clay at OCR 1.2 and 4.8, then load tested from 1 hour to 90 days.

Key resultJacked-in piles started with higher shaft friction, but driven piles set up faster and ended higher in the long term, attributed to greater soil disturbance during driving.

See Figure 3

Particle morphology

3D particle shape from 2D images

A flat grain resting on its largest face looks round from above, so 2D images overestimate sphericity. Using a sequential sieving test, run like a normal sieve test but stopped at several time steps, together with X-ray micro-CT of more than 3,000 particles per material, we linked 2D shape indices to true 3D sphericity.

Key resultThe initial passing rate correlates strongly with 3D sphericity, and grading curves from 3D imaging agree with sieve analysis, while 2D ones do not without correction.

Read the paper

03 · Research in figures

Three findings, drawn from the papers

Every element below follows the published or submitted work; schematics are labeled where they are not to scale.

Figure 1 · Ph.D. research · Particle degradation

From pile driving to the laboratory: three ways glauconite breaks down

Impact driving loads the surrounding soil in three idealized stress regimes. Each one is reproduced in the laboratory with a matching degradation method.

Idealized stress zones around an impact-driven pile A pile driven into glauconite sand. Zone 1, directly below the pile tip, is compressed one-dimensionally, with radial stress lower than vertical stress. Zone 2, a shear band spreading outward and downward from the tip corner, combines intense shear with high normal stress, with radial and vertical stress about equal. Zone 3, the soil along the pile shaft, is sheared intensely under lower normal stress, with radial stress higher than vertical stress. 1 impact hammer 3 along the shaft · σr > σv σv σr τ 2 shear band · σr ≈ σv σv σr τ σv σr 1 below the tip · σr < σv glauconite sand
  1. Along the shaft → dispersion-cup mixing

    σr > σv · high shear · low normal stress · abundant free water

    Slurry mixing in an ASTM dispersion cup, also representative of jetted piles and tunnel-boring faces.

  2. Shear band at the tip → ball milling

    σr ≈ σv · high shear · high normal stress · natural water content

    Moist soil milled with steel balls in a Los Angeles abrasion drum.

  3. Below the tip → 1D compression

    σr < σv · high compression · low shear

    Oedometer loading to 50 MPa, similar to cone tip resistance in very dense glauconite sand.

Dispersion cupReleased plastic clay minerals: plasticity rose as particles broke down.

Ball millingA similar gain in fines, but mostly non-plastic clay-size particles: plasticity unchanged or even lower.

1D compressionCompression to 50 MPa produced only small changes.

Takeaway: classification by particle size alone is not enough for degraded glauconite. The stress regime and the availability of free water during degradation control whether the new fines make the soil plastic.

Concept after Shafiei, Jaffé, Westgate & DeGroot, “Effect of particle degradation mechanisms on glauconite sand behavior” (submitted, ASCE Geo-Congress 2027). Stress zones are idealized; element sketches show undeformed (dashed) and deformed (solid) shapes. Soils: Hornerstown and Navesink glauconite sands, Sewell, New Jersey.

Figure 2 · Offshore site investigation

Which CPTu set-ups reduced thrust in glauconite sand?

  • Standard friction reducer Reference
  • Larger 15 cm² cone Reduced thrust
  • Larger-diameter reducer Reduced thrust
  • Water jetting at the upper bevel Reduced thrust
  • Longer reducer No improvement
  • Multiple reducers along the rod No improvement
  • Glauconite crushes under shear and compression, so CPTu thrust builds from both high tip resistance and high rod friction.
  • The larger cone, the larger-diameter reducer, and water jetting allowed deeper penetration, but effectiveness was layer-specific.
  • Result: practical guidance for deeper, more cost-effective site characterization where thick glauconite layers occur.
Schematic, not to scale (cone sizes proportional); 10 cm² cones unless noted. Field program at a New Jersey site in two glauconite sand formations. Source: Westgate, Senanayake, Shafiei & DeGroot (2026), Canadian Geotechnical Journal 63: 1–8.

Figure 3 · Deep foundations

The calibration chamber behind the pile setup study

Calibration chamber with instrumented model pile A rigid steel cylinder 400 millimeters in diameter and 1000 millimeters tall, filled with kaolinite clay with a saturated sand drainage layer along the walls. A loading plate applies a 43.2 kilopascal surcharge. A CPT-size model pile is embedded 560 millimeters, leaving 300 millimeters of clay below its tip. Strain gauges and pore-pressure transducers are placed at the top, middle and tip of the pile, 150 millimeters apart. A pneumatic jack, load cell and LVDT perform the static load tests. pneumatic jack load cell LVDT SG PTS 150 mm kaolinite clay OCR 1.2 or 4.8 surcharge 43.2 kPa rigid steel cylinder saturated sand drain 1000 mm Ø 400 mm 560 mm 300 mm
  • driven or jacked-in
  • load tests 1 h – 90 d
  • SG = strain gauge
  • PTS = pore-pressure transducer
  • Installation generated higher excess pore pressures in normally consolidated (NC) clay than in overconsolidated (OC) clay.
  • OC clay gave higher shaft friction than NC clay, both at the end of installation and after setup.
  • Jacked-in piles started higher, but driven piles set up faster and reached greater long-term friction.
  • Setup was split into pore-pressure dissipation and non-pore-pressure (aging) parts, and a relation was proposed for the gain in pile stiffness over time.
Drawn to scale from the chamber schematic (dimensions in mm). Clay was consolidated layer by layer with a pneumatic jack. Source: Fakharian, Shafiei & Hafezan (2023), Canadian Geotechnical Journal 60(4): 488–503.

04 · Publications

Publications & presentations

Journal articles, conference work, and thesis research. A complete, up-to-date list is on Google Scholar.

Journal articles

  1. 2026 Journal article

    Mitigation of CPT thrust force through glauconite sand

    Westgate, Z. J., Senanayake, A., Shafiei, M., & DeGroot, D. J.

    Canadian Geotechnical Journal, 63, 1–8 · doi:10.1139/cgj-2026-0117

    • Field CPTu
    • 2 glauconite formations, NJ
    • Thrust-reduction methods
    Publisher (DOI) ResearchGate
    Summary

    Glauconite sands crush easily under shear and compression, producing high piezocone (CPTu) penetration forces from a combination of high tip resistance and high rod friction. Routine fixes, such as larger cones and friction reducers, can still lead to early refusal. A CPTu field investigation at a New Jersey test site in two glauconite formations compared larger cones, standard friction reducers, longer reducers, larger-diameter reducers, multiple reducers spaced along the rod, and water jetting with a standard reducer. A larger 15 cm² cone, a larger-diameter reducer on a 10 cm² cone, and water jetting from the upper bevel of a 10 cm² cone significantly reduced thrust and allowed greater penetration, although effectiveness was layer-specific; longer or multiple standard reducers gave no improvement.

    Cite
    @article{westgate2026mitigation,
      title   = {Mitigation of CPT thrust force through glauconite sand},
      author  = {Westgate, Zachary J. and Senanayake, Asitha and Shafiei, Morteza and DeGroot, Don J.},
      journal = {Canadian Geotechnical Journal},
      volume  = {63},
      pages   = {1--8},
      year    = {2026},
      doi     = {10.1139/cgj-2026-0117}
    }
  2. 2024 Journal article

    Quantifying three-dimensional sphericity indices of irregular fine particles from 2D images through sequential sieving tests

    Kaviani-Hamedani, F., Esmailzade, M., Adineh, K., Shafiei, M., & Shirkavand, D.

    Granular Matter, 26(1), Article 13 · doi:10.1007/s10035-023-01376-1

    • X-ray micro-CT, 3,000+ particles/material
    • 7 natural + 7 synthetic materials
    • Zingg flatness & elongation
    Publisher (DOI) ResearchGate
    Summary

    Proposes a way to predict 3D sphericity from ordinary 2D image analysis using a new sieving procedure. The 3D sphericity of grains from seven irregular granular materials (more than 3,000 particles each) was measured from X-ray micro-CT slices and compared with 2D indices from SEM image processing; seven semi-regular synthetic materials extended the range of shapes. In the sequential sieving test, run like a conventional sieve test but at several time steps, the initial passing rate correlated strongly with 3D sphericity. The study gives correlations between 2D and 3D sphericity, two equations for the most frequent Zingg flatness and elongation ratios, and a correction that brings 2D grading curves into line with 3D imaging and sieve analysis.

    Cite
    @article{kavianihamedani2024quantifying,
      title     = {Quantifying three-dimensional sphericity indices of irregular fine particles from 2D images through sequential sieving tests},
      author    = {Kaviani-Hamedani, Farzad and Esmailzade, Mohammad and Adineh, Kianoush and Shafiei, Morteza and Shirkavand, Danial},
      journal   = {Granular Matter},
      volume    = {26},
      number    = {1},
      pages     = {13},
      year      = {2024},
      publisher = {Springer},
      doi       = {10.1007/s10035-023-01376-1}
    }
  3. 2023 Journal article

    Investigation of soil setup effects on pile response in clay considering overconsolidation ratio and installation method through physical modeling

    Fakharian, K., Shafiei, M., & Hafezan, S.

    Canadian Geotechnical Journal, 60(4), 488–503 · doi:10.1139/cgj-2021-0686

    • Kaolinite, OCR 1.2 & 4.8
    • Driven vs. jacked-in
    • Load tests 1 h – 90 d
    Publisher (DOI)
    Summary

    Investigates how soil setup changes the axial resistance and stiffness of small-scale piles in clay, focusing on overconsolidation ratio and installation method. In a purpose-built consolidation chamber, an instrumented model pile was driven or jacked into saturated kaolinite at OCR 1.2 (NC) and 4.8 (OC) and load tested from 1 hour to 90 days. Installation induced higher pore pressures in NC clay, and OC clay gave higher shaft friction both at the end of installation and after setup. Jacked-in piles had higher friction at the end of installation, but driven piles, with their higher setup rate, reached greater long-term friction, attributed to more soil disturbance during driving. The contributions of excess pore-pressure dissipation and non-pore-pressure components were separated, and a relation was proposed for the change in pile stiffness over time.

    Cite
    @article{fakharian2023investigation,
      title   = {Investigation of soil setup effects on pile response in clay considering overconsolidation ratio and installation method through physical modeling},
      author  = {Fakharian, Kazem and Shafiei, Morteza and Hafezan, Salar},
      journal = {Canadian Geotechnical Journal},
      volume  = {60},
      number  = {4},
      pages   = {488--503},
      year    = {2023},
      doi     = {10.1139/cgj-2021-0686}
    }

Conference papers & presentations

  1. 2027 Conference paper · submitted

    Effect of particle degradation mechanisms on glauconite sand behavior

    Shafiei, M., Jaffé, D., Westgate, Z. J., & DeGroot, D. J.

    ASCE Geo-Congress 2027 · abstract accepted, full paper submitted

    • 1D compression · ball milling · dispersion cup
    • Relative breakage index
    • Plasticity of degraded fines

    Glauconite sands degrade easily, which changes how they classify and behave in site characterization, pile–soil interaction, and tunnel boring. Two natural glauconite sands were degraded with three laboratory methods matched to the stress fields around a driven pile. Dispersion-cup mixing and ball milling degraded the soils extensively, while one-dimensional compression to 50 MPa produced only small changes. Dispersion-cup mixing released more clay minerals and raised plasticity; ball milling released mostly non-plastic clay-size particles, with negligible or even lower plasticity for a similar gain in fines. Particle-size classification alone is therefore insufficient: laboratory degradation should reflect the stress regime and free-water conditions of the field application.

  2. 2026 Poster

    Effect of laboratory-induced degradation on the plasticity of authigenic glauconite sands

    Shafiei, M., Guo, D., DeGroot, D. J., & Westgate, Z. J.

    Tufts 4th Annual Symposium in Geotechnical Engineering, “Reconciling Laboratory Testing, Numerical Modeling, and Field Applications,” Tufts University, Medford, MA · February 7, 2026

Thesis

  1. 2018 M.Sc. thesis

    Effect of installation method and pile type on soil setup using consolidation chamber physical modeling

    Shafiei, M., & Fakharian, K.

    M.Sc. thesis and conference proceedings, Amirkabir University of Technology (Tehran Polytechnic)

    Experimental investigation of how pile installation method (driven vs. jacked) and effective consolidation stress level influence time-dependent shaft setup and the evolution of bearing capacity in a pressurized consolidation chamber.

05 · News & recognition

News & recognition

  1. Upcoming
    Conference

    Abstract accepted for ASCE Geo-Congress 2027

    First-author paper “Effect of particle degradation mechanisms on glauconite sand behavior,” with an undergraduate co-author. Summary

  2. Feb 7, 2026
    Poster

    Poster at the Tufts 4th Annual Symposium in Geotechnical Engineering

    “Effect of laboratory-induced degradation on the plasticity of authigenic glauconite sands,” Tufts University, Medford, MA.

  3. 2026
    Publication

    “Mitigation of CPT thrust force through glauconite sand” published

    Canadian Geotechnical Journal, 63, 1–8. Details

  4. Nov 10, 2025
    Feature

    ARROW Student Spotlight

    Featured by ARROW, the Academic Center for Reliability & Resilience of Offshore Wind, for research on glauconite sand behavior in offshore wind areas. Read the spotlight

  5. Oct 2025
    Training

    Completed “Cone Penetration Testing for Geotechnical Applications”

    ConeTec & Menard course presented by Dr. Peter Robertson and colleagues, Waltham, MA. 7.0 Professional Development Hours (Professional Engineering & Geology).

  6. 2025
    Feature

    Highlighted in the ARROW 2025 Annual Report

    Included in the report’s Student Highlights for evaluating the degradation of glauconite sand under static and cyclic loading in onshore and offshore deposits.

06 · Teaching & mentoring

Teaching, research & mentoring

  • University Instructor

    Department of Civil & Environmental Engineering, UMass Amherst

    Lead laboratory and course instructor for undergraduate engineering mechanics and geotechnical engineering courses.

  • Graduate Research Assistant · ARROW student researcher

    Offshore Geotechnics & Foundation Mechanics Group, UMass Amherst

    Laboratory and field research on glauconite sand for offshore wind foundations, including field CPTu testing within the Piling in Glauconitic Sand (PIGS) Joint Industry Project.

  • Undergraduate research

    Geotechnical laboratory, UMass Amherst

    Works with undergraduate researchers on glauconite degradation testing, including an undergraduate co-author on the ASCE Geo-Congress 2027 paper.

07 · Education

Education & professional development

  1. Ph.D., Civil & Environmental Engineering (Geotechnical)

    2021 – present

    University of Massachusetts Amherst

    Ph.D. candidate advised by Prof. Don J. DeGroot and Prof. Zachary J. Westgate. Research on the degradation and behavior of glauconite sand for offshore wind foundations.

  2. M.Sc., Civil & Geotechnical Engineering

    2015 – 2018

    Amirkabir University of Technology (Tehran Polytechnic)

    Graduated with highest academic honors. Designed and operated a large-scale pressurized consolidation calibration chamber for physical modeling of deep foundations under Prof. Kazem Fakharian.

  3. B.Sc., Civil Engineering

    2010 – 2015

    University of Tabriz

    Comprehensive training in solid mechanics, structural analysis, foundation engineering, and experimental soil mechanics.

Professional development

  • Cone Penetration Testing for Geotechnical Applications

    ConeTec & Menard · Waltham, MA · October 2025

    Course presented by Dr. Peter Robertson, Kelly Cabal, Eric Rundstrom, and Jorge Fuentes. 7.0 Professional Development Hours (Professional Engineering & Geology), accredited by The Practicing Institute of Engineering.

08 · Expertise

Methods, standards & tools

Hands-on experience across field testing, laboratory degradation and index testing, instrumentation, and analysis.

Field & laboratory testing

From full-scale piezocone soundings to grain-scale degradation and index tests.

  • Field CPTu (piezocone)
  • Calibration-chamber modeling
  • High-pressure oedometer (50 MPa)
  • Ball milling (LA abrasion)
  • Dispersion-cup degradation
  • Hydrometer & sieve analysis
  • Fall-cone Atterberg limits
  • X-ray micro-CT & SEM image analysis

Standards

Testing and classification standards used in my field and laboratory work.

  • ASTM D5778 · CPTu
  • ASTM D1143 · pile load test
  • ASTM D6913 · sieve analysis
  • ASTM D7928 · hydrometer
  • ASTM D2435 · consolidation
  • ASTM D2487 · USCS
  • ISO 17892-12 · Atterberg limits
  • API RP 2GEO · offshore
  • ISO 19901-8 · marine soils

Instrumentation & analysis

Sensors, data acquisition, numerical modeling, and scientific computing.

  • Pore-pressure transducers
  • Strain gauges · load cells · LVDTs
  • PLAXIS 2D & 3D
  • FLAC · GeoStudio
  • Python (NumPy, SciPy, pandas)
  • MATLAB · ImageJ
  • gINT · CPT-Pro

09 · Contact

Get in touch

Open to research collaboration, speaking invitations, and industry inquiries.

Email

mortezaashafiei [at] gmail [dot] com

Research collaborations, industry inquiries, and website correspondence.

mshafiei [at] umass [dot] edu

University correspondence, students, and teaching.

Office & laboratory

Room 201, Engineering Lab II

Department of Civil & Environmental Engineering
University of Massachusetts Amherst
Amherst, MA 01003, USA

Curriculum vitae

Education, publications, presentations, appointments, and technical skills in one document.